QuickPrime Plus
1. Description
Firestone QuickPrime Plus is designed to clean and prime the RubberGard EPDM membrane and/or
substrate prior to application of QuickSeam Products, Pourable Sealer or Lap Sealant. QuickPrime
Plus must be applied with a QuickScrubber or QuickScrubber Plus pad and handle.
2. Preparation
Surfaces to be primed must be clean, dry and free of foreign materials, talc and dirt. Pre-cleaning
with Splice Wash may be required. Stir QuickPrime Plus thoroughly before and during use. When
exposed to lower temperatures for a prolonged period of time, restore to room temperature prior
to use. Pour the required amount of QuickPrime Plus into a bucket for ease of application.
3. Application
Apply QuickPrime Plus to the RubberGard EPDM surfaces and/or other substrates to receive
QuickSeam products with the QuickScrubber or QuickScrubber Plus pad and handle using long
back and forth strokes with moderate to heavy pressure along the length of the area. Continue
until surfaces become dark grey in colour (no streaking or puddling). Factory seams require
parallel as well as perpendicular application motions along the factory seam. When using the
QuickScrubber Plus pad and handle, make sure to apply sufficient pressure during application so
the pad holder flattens to allow the total surface of the pad to contact with the RubberGard EPDM
membrane. Allow the primed surfaces to dry completely according to the touch-push test (usually
less than 10 minutes) before applying QuickSeam products.
4. Coverage
Thining is not allowed. The following rates can be achieved with 1 gallon.
Standard seam with 76 mm (3”) Splice Tape: 60 lm – 2 sides.
B.I.S. seam with 152 mm (6”) Splice Tape: 45 lm – 2 sides.
QuickSeam R.M.A. Strip: 55 lm – 1 side.
QuickSeam RPF Strip: 60 lm – 1 side.
QuickSeam SA Flashing: 35 lm – 1 side.
QuickSeam FormFlash 300 mm (12”): 45 lm – 1 side.
QuickSeam Flashing 127 mm (5”): 100 lm – 1 side.
QuickSeam Batten Cover: 90 lm – 1 side.
5. Characteristics
Technical Base Synthetic rubber polymers
Colour Translucent grey
Solvents Heptane, toluene
Solids (%) 16 - 18
Viscosity Very thin, free flowing
Specific gravity 0.793 (Water = 1)
Flash point (°C) -17.8
6. Packaging / Storage / Shelf Life
Packaging: 3.8 l (1 gallon) pails (4 pails per box) and 11.4 l (3 gallon) pails.
Storage: Store in original unopened containers at temperatures between 15°C and 25°C. Keep
the material out of direct sunlight until ready for application.
Shelf Life: 12 months can be expected if stored in above-mentioned conditions. Shelf life information
is only a recommendation and not a fact of life. The real expiration date highly depends on
the history of storage and handling of the accessories. Quality and applicability should thus always
be verified: when mixed, product should stir into a smooth and homogeneous blend product with
no evidence of major clumping or separation/phasing.
7. Precautions
Flammable. Keep away from sources of ignition. Do not smoke when using. For professional use
only. Use only in well ventilated areas. Avoid contact with skin and eyes. Refer to Material Safety
Data Sheets. Keep out of the reach of children.
1. Description
Firestone QuickPrime Plus is designed to clean and prime the RubberGard EPDM membrane and/or
substrate prior to application of QuickSeam Products, Pourable Sealer or Lap Sealant. QuickPrime
Plus must be applied with a QuickScrubber or QuickScrubber Plus pad and handle.
2. Preparation
Surfaces to be primed must be clean, dry and free of foreign materials, talc and dirt. Pre-cleaning
with Splice Wash may be required. Stir QuickPrime Plus thoroughly before and during use. When
exposed to lower temperatures for a prolonged period of time, restore to room temperature prior
to use. Pour the required amount of QuickPrime Plus into a bucket for ease of application.
3. Application
Apply QuickPrime Plus to the RubberGard EPDM surfaces and/or other substrates to receive
QuickSeam products with the QuickScrubber or QuickScrubber Plus pad and handle using long
back and forth strokes with moderate to heavy pressure along the length of the area. Continue
until surfaces become dark grey in colour (no streaking or puddling). Factory seams require
parallel as well as perpendicular application motions along the factory seam. When using the
QuickScrubber Plus pad and handle, make sure to apply sufficient pressure during application so
the pad holder flattens to allow the total surface of the pad to contact with the RubberGard EPDM
membrane. Allow the primed surfaces to dry completely according to the touch-push test (usually
less than 10 minutes) before applying QuickSeam products.
4. Coverage
Thining is not allowed. The following rates can be achieved with 1 gallon.
Standard seam with 76 mm (3”) Splice Tape: 60 lm – 2 sides.
B.I.S. seam with 152 mm (6”) Splice Tape: 45 lm – 2 sides.
QuickSeam R.M.A. Strip: 55 lm – 1 side.
QuickSeam RPF Strip: 60 lm – 1 side.
QuickSeam SA Flashing: 35 lm – 1 side.
QuickSeam FormFlash 300 mm (12”): 45 lm – 1 side.
QuickSeam Flashing 127 mm (5”): 100 lm – 1 side.
QuickSeam Batten Cover: 90 lm – 1 side.
5. Characteristics
Technical Base Synthetic rubber polymers
Colour Translucent grey
Solvents Heptane, toluene
Solids (%) 16 - 18
Viscosity Very thin, free flowing
Specific gravity 0.793 (Water = 1)
Flash point (°C) -17.8
6. Packaging / Storage / Shelf Life
Packaging: 3.8 l (1 gallon) pails (4 pails per box) and 11.4 l (3 gallon) pails.
Storage: Store in original unopened containers at temperatures between 15°C and 25°C. Keep
the material out of direct sunlight until ready for application.
Shelf Life: 12 months can be expected if stored in above-mentioned conditions. Shelf life information
is only a recommendation and not a fact of life. The real expiration date highly depends on
the history of storage and handling of the accessories. Quality and applicability should thus always
be verified: when mixed, product should stir into a smooth and homogeneous blend product with
no evidence of major clumping or separation/phasing.
7. Precautions
Flammable. Keep away from sources of ignition. Do not smoke when using. For professional use
only. Use only in well ventilated areas. Avoid contact with skin and eyes. Refer to Material Safety
Data Sheets. Keep out of the reach of children.
| SKU | Firestone_Quick_Prime_Plus_1_Gallon_Tin |
|---|---|
| g/sm | No |
| Size | No |
| Width | No |
| Color | No |
| Price Per | No |
| Tailored Box Size | N/A |
My Cart
You have no items in your shopping cart.
Compare Products
You have no items to compare.
